Methods and mechanisms for uniformly refining deformed mixed and coarse grains inside a solution-treated Ni-based superalloy by two-stage heat treatment

The uniform refinement mechanisms and methods of deformed mixed and coarse grains inside a solution-treatment Ni-based superalloy during two-stage annealing treatment have been investigated.The two-stage heat treatment experiments include an aging annealing treatment(AT)and a subsequent recrystallization annealing treatment(RT).The object of AT is to precipitate some δ phases and consume part of storage energy to inhibit the grain growth during RT,while the RT is to refine mixed and coarse grains by recrystallization.It can be found that the recrystallization grains will quickly grow up to a large size when the AT time is too low or the RT temperature is too high,while the deformed coarse grains cannot be eliminated when the AT time is too long or the RT temperature is too low.In addition,the mixed microstructure composed of some abnormal coarse recrystallization grains(ACRGs)and a large number of fine grains can be observed in the annealed specimen when the AT time is 3 h and RT tem-perature is 980℃.The phenomenon attributes to the uneven distribution of δ phase resulted from the heterogeneous deformation energy when the AT time is too short.In the regions with a large number of δ phases,the recrystallization nucleation rate is promoted and the growth of grains is limited,which results in fine grains.However,in the regions with few δ phases,the recrystallization grains around grain boundaries can easily grow up,and the new recrystallization nucleus is difficult to form inside grain,which leads to ACRGs.Thus,in order to obtain uniform and fine annealed microstructure,it is a prereq-uisite to precipitate even-distributed δ phase by choosing a suitable AT time,such as 12 h.Moreover,a relative high RT temperature is also needed to promote the recrystallization nucleation around δ phase.The optimal annealing parameters range for uniformly refining mixed crystal can be summarized as:900℃×12 h+990℃×(40-60 min)and 900℃×12 h+1000℃×(10-15 min).     

针刺复合生态土工布的制备及植生性能研究

以黏胶短纤维和再生植物纤维为主要原料,采用短纤维干法成网-针刺加固工艺,在针刺密度为60～160针/cm2、针刺深度为3.5～ 12.0 mm、针刺频率为720～ 940次/min的条件下,制备单位面积质量在196～979g/m2、厚度在3.6～ 14.4 mm、再生植物纤维质量分数在39.6％ ～ 70.9％的针刺复合生态土工布,用于植生护坡.性能测试和植物种植试验结果表明:针刺复合生态土工布具有较好的力学性能和吸水保水性能,且对植物的生长具有良好的促进作用;随着针刺复合生态土工布单位面积质量的增加,其力学性能增加,吸水保水性能变好,发芽率、植株高度和植株质量也均呈现出增加的趋势.     

Dynamic hierarchical collaborative caching scheme in ultra-dense networks

Pushing popular contents to the edge of the network can meet the growing demand for data traffic, reduce latency and relieve the pressure of the backhaul. However, considering the limited storage space of the base stations, it is impossible to cache all the contents, especially in ultra-dense network ( UDN). Furthermore, the uneven distribution of mobile users results in load imbalance among small base stations (SBSs) in both time and space, which also affects the caching strategy. To overcome these shortcoming, the impact of the changing load imbalance in UDN was investigated, and then a dynamic hierarchical collaborative caching (DHCC) scheme was proposed to optimize latency and caching hit rate. The storage of the SBS is logically divided into the independent caching layer and the collaborative caching layer. The independent caching layer caches the most popular contents for local users爷interest, and the collaborative caching layer caches contents as much as possible for the benefit of content diversity in the region. Different SBSs have respective storage space layer division ratios, according to their real-time traffic load. For SBSs with heavy load, the independent caching layers are allocated with more space. Otherwise, the collaborative caching layers could store more contents with larger space. The simulation results show that, DHCC improved both transmission latency and hit rate compared with existing caching schemes.     

Negative thermal quenching CsPbBr3 glass-ceramic based on intrinsic radiation and vacancy defect co-induced dual-emission

Halide perovskite glass-ceramic has recently moved into the center of the attention of perovskite research due to their potential for temperature sensing. However, quantum dots glass-ceramic with excellent luminescence performance still needs to be combined with rare-earth (RE) ions to accurately measure temperature. In this work, a novel non-RE doped dual-emission (460 nm and 512 nm) CsPbBr₃ quantum dots was obtained in telluride glass via the friction crystallization method, where 512 nm was derived from intrinsic luminescence of quantum dots, and 460 nm was originated from thermally induced bromine vacancy, which can be used for temperature sensing. Fluorescence intensity ratio results indicate that the relative sensitivity of dual-emission could reach 5.6 % K^?1 at 323 K. The discovery of non-RE doped CsPbBr₃ QDs glass-ceramic with negative thermal quenching uncovers a new optional sensing glass material that surpass traditional RE-doped QDs glass by their tunability and sensitivity.     

High-Throughput Screening for Phase-Change Memory Materials

Phase change memory (PCM) is an emerging non-volatile data storage technology concerned by the semiconductor industry. To improve the performances, previous efforts have mainly focused on partially replacing or doping elements in the flagship Ge-Sb-Te (GST) alloy based on experimental “trial-and-error” methods. Here, the current largest scale PCM materials searching is reported, starting with 124 515 candidate materials, using a rational high-throughput screening strategy consisting of criteria related to PCM characteristics. In the results, there are 158 candidates screened for PCM materials, of which ≈68% are not employed. By further analyses, including cohesive energy, bond angle analyses, and Born effective charge, there are 52 materials with properties similar to the GST system, including Ge₂Bi₂Te₅, GeAs₄Te₇, GeAs₂Te₄, so on and other candidates that have not been reported, such as TlBiTe₂, TlSbTe₂, CdPb₃Se₄, etc. Compared with GST, materials with close cohesive energy include AgBiTe₂, TlSbTe₂, As₂Te₃, TlBiTe₂, etc., indicating possible low power consumption. Through further melt-quenching molecular dynamic calculation and structural/electronic analyses, Ge₂Bi₂Te₅, CdPb₃Se₄, MnBi₂Te₄, and TlBiTe₂ are found suitable for optical/electrical PCM applications, which further verifies the effectiveness of this strategy. The present study will accelerate the exploration and development of advanced PCM materials for current and future big-data applications.     

Solution-Synthesized Multifunctional Janus Nanotree Microswimmer

Synthetic active matters are perfect model systems for non-equilibrium thermodynamics and of great potential for novel biomedical and environmental applications. However, most applications are limited by the complicated and low-yield preparation, while a scalable synthesis for highly functional microswimmers is highly desired. In this paper, an all-solution synthesis method is developed where the gold-loaded titania-silica nanotree can be produced as a multi-functional self-propulsion microswimmer. By applying light, heat, and electric field, the Janus nanotree demonstrated multi-mode self-propulsion, including photochemical self-electrophoresis by UV and visible light radiation, thermophoresis by near-infrared light radiation, and induced-charge electrophoresis under AC electric field. Due to the scalable synthesis, the Janus nanotree is further demonstrated as a high-efficiency, low-cost, active adsorbent for water decontamination, where the toxic mercury ions can be reclaimed with enhanced efficiency.